Mon panier
0 article0,00 $US

PiJuice HAT – Portable Power for Raspberry Pi

PiJuice HAT – Portable Power for Raspberry Pi

With the PiJuice you can increase the performance of one of the most powerful systems even more. Your Raspberry Pi will be more portable than ever, thus removing limitations on its capabilities.

Prix 71,00 $US

Membres 64,00 $US

Disponible

Ce produit sera expédié dans 5 jours

Détails

Features

  • Onboard 1820 mAh Lipo / LiIon battery for ~4 to 6 hours in constant use
  • A Full Uninterrupted / Uninterruptable Power Supply solution.
  • Designed for the Raspberry Pi A+, B+, 2B, 3B and 3B+ but also compatible with Raspberry Pi Zero v1.3 and Raspberry Pi Zero Wireless.
  • Integrated Real Time Clock
  • Onboard intelligent on/off switch
  • Low power deep-sleep state with wake on interrupt/calendar event
  • Programmable multi-colored RGB led (x2) and buttons (x3) with super simple user-configurable options
  • Hardware watchdog timer to keep your Raspberry Pi on and working in mission-critical remote applications
  • Full power management API available to Raspberry Pi OS with auto shutdown capability when running low on batteries
  • Raspberry Pi HAT compatible layout, with onboard EEPROM for easy plug and play operation
  • Low profile design to fit inside lots of existing Raspberry Pi cases!
  • Enhanced graphical user interface (GUI) available for easy install (via APT)
  • Customisable scripts for enhanced flexibility and full report of battery status
  • All GPIOs available via stackable header for ease of expandability and connectivity
  • Charge via on-board micro USB or via the Raspberry Pi micro USB (or from onboard pin headers)
  • Batteries can be charged with a different type of sources and voltages
  • Replace the battery without downtime. Compatible with any single cell LiPo or LiIon battery
  • Fully CE and FCC tested design.

Specifications

  • The EEPROM can be disabled and its I2C address changed for increased compatibility with other boards
  • BP7X battery - original battery from Motorola Droid 2 (A955) - 1820 mAh battery
  • Microcontroller is an ST Micro STM32F030CCT6 ARM Cortex-M0, 48 MHz, F64KB, R8KB, I2C, SPI, USART, 2.4 V - 3.6 V
  • Charge IC - BQ24160RGET Charger IC Lithium-Ion/Polymer, 2.5 A, 4.2 V - 10 V
  • Fuel gauge IC - LC709203FQH-01TWG Battery Fuel Gauge, 1-Cell Li-ion, 2.8%
  • EEPROM - CAT24C32WI-GT3 EEPROM, I2C, 32 KBIT, 400 kHz, 1V7-5V5
  • Optional spring pin - Mil-Max 0929-7-15-20-77-14-11-0
  • Compatible with any 4 pin battery on board that can be used with 00-9155-004-742-006 battery contacts from AVX including the BP7X, BP6X, and any compatible batteries including the 1600mAh and 2300mAh ones from CameronSino (CS-MOA853SL and CS-MOA855XL)
  • There is an onboard 4 pin screw terminal block for larger off board batteries. Any single cell LiPo / LiIon is compatible. However, you use your own sourced battery at your own risk.
    We HIGHLY RECOMMEND using a battery with an internal protection circuit and an NTC (temp sensor)
  • Optional header for offboard button - connected to the same output as SW1
  • 6 pin breakout header - with two GPIO from the ARM Cortex-M0, VSYS, 5V0, 3V3, GND connections
  • A header for optional off board solar panel/wind turbine etc.
  • Optional RF Shield attachment - Harwin S02-20150300 (can also double as an inexpensive heatsink)
  • Input voltage range - 4.2 V - 10 V
  • Output voltage - 3.3 V and 5 V
  • Output amperage - maximum current at 5 V gpio is 2.5 A and at VSYS output 2.1 A, but also this depends heavily on battery capacity. For BP7X have measured around 1.1 A at 5V GPIO and around 1.6 A at VSYS output. Obviously, this also depends heavily on the current draw demanded by the Raspberry Pi/device itself. To achieve a maximum of 2.5 A it will need battery over 3500 mAh.
  • Boxed weight - 96 g
  • Boxed dimensions - 12.2 cm x 10.8 cm x 3.5 cm
  • Unboxed weight - 57 g
  • Unboxed dimensions - 6.5 cm x 5.6 cm x 2 cm

PiJuice HAT box contains

  • 1 x PiJuice HAT
  • 1 x Battery and battery surround
  • 1 x PiJuice guide
  • 4 x Mounting posts attached to PiJuice
  • 8 x Mounting screws (4 are already assembled to the board)
  • 1 x Pogo pin
  • 3 x Stickers


Check also: PiJuice GitHub

Réf. 18512

Video

Rédigez votre propre commentaire

Quelle note donneriez-vous à ce produit ? *

1 2 3 4 5
Qualité
Valeur
Prix
  • Reload captcha

CONTACTEZ-NOUS